The Video Course teaches you everything about modern cars.

Although they are considerably more complicated than manual gearboxes, withcontrol and operating functions in addition to the gears, modern automatictransmissions are less likely to give problems than their manualcounterparts.

The main reason for this greater relibility is the fact that the gears areengaged smoothly by the operation of internal clutches and brake bands underautomatic control, so minimizing the possibility of maltreatment, shock loadingand gear crashing, and the mechanical damage that can result from these.

When problems do occur they are often caused by the external controllinkages, or a low fluid level, and can often be dealt with without having tostrip the transmission. Internal transmission faults generally call forspecialist equipment and knowledge and are best left to a service engineer -after you have checked to make sure that the problem really is internal.

In this video, I show you how to shift gears in an automatic car. Your car must be equipped with a shift lever that has a gear selector option for this to wo. In most car and truck applications, the DCT functions as an automatic transmission, requiring no driver input to change gears. The first DCT to reach production was the Easidrive automatic transmission introduced on the 1961 Hillman Minx mid-size car.

The close linkage between engine and transmission can make faultfindingdifficult, so before you blame the transmission for bad performance you need tocheck that the engine is in good tune. Bumpy starts and gear shifts, forexample, can be caused by a high engine idle speed.

Car Gears In Order

If you suspect overheating has occurred, check that the ventilation openings in the torque convertor bell housing have not become blocked with dirt or oil build-up. Clean them out using an engine cleaner and a stiff brush if necessary.Where an oil cooler is fitted make sure the hoses to and from the transmission are properly connected and not kinked. Also check that the oil cooler radiator is not blocked by dirt— clean the core very carefully with degreaser and a soft paint brush. Finally, drain the transmission and refill with fresh fluid. Use only the type of automatic transmission fluid (ATF) recommended by the manufacturer and take great care not to get any other substance in the fluid.

Simple checks

By far the most common cause of trouble with an automatic gearbox isincorrect fluid level (see sideline, opposite). If that seems to be all right,you need to do a test to discover whether the problem is in the gearbox, thetorque convertor or the engine.

A general lack of performance with poor acceleration and bad hill startingcan be due to a fault in the torque convertor. With some models it is possibleto check the convertor by carrying out a stall test, though this procedure isnot suitable in all cases. Find out from your manual (or your dealer) if youcan do the test, and also what is the specified stall speed for yourtransmission.

With the engine running and both the engine and transmission properly warmedup apply the footbrake firmly, select the lowest gear and fully depress theaccelerator pedal so that the engine revs up - keep it going until the revsstop rising.

Using an accurate rev counter, make a note of that engine speed (called thestall speed). Release the accelerator and return the selector to neutral. Donot hold the transmission in the stalled condition for more than ten seconds oryou may cause serious damage.

Compare the measured stall speed to the specified value. A reading justbelow the specified value means that the engine is probably out of tune, but asignificantly lower reading (say 500rpm down) shows that there is a convertorfault. A high stall speed points to a problem with the fluid supply to theconvertor, or to an internal fault in the rest of the transmission. To find outexactly where the problem lies, you will need to do the tests shown in thefaultfinder chart below.

First check the fluid level. A need for frequent topping up shows that there is a leak somewhere in the transmission which should be traced and put right as soon as possible.

Try standing the car over some newspaper laid out on the ground. Start the engine and operate the transmission lever a couple of times. Any drips will show up on the paper and their position will give you a good idea where the fluid is coming from. If the level is all right, you should check the fluid condition. The condition of the transmission fluid can often provide a useful guide to transmission condition. Put a smear of fresh fluid on some white kitchen paper to give a comparison and then use the dipstick to obtain a sample of the fluid from the transmission, again smearing it on paper.

Hot fluid is thinner and will have a less pronounced colour but the two samples should appear much the same. Dark brown discoloration shows that the fluid has been overheated, while the presence of black specks points to heavy wear of the internal clutches and brake bands and an internal investigation will probably be needed — especially if your other tests show the transmission is not working properly.

On some cars, the parking brake is operated by a separate cable from the rest of the gear selector linkage. It must be correctly set or the brake may not work.

Find out from your workshop manual where the adjuster is—it may be at the gearbox or somewhere under the bonnet.

Select 'park', then adjust the cable so that the parking brake pulls on. Then select neutral and check that the parking brake releases. You can do this by gently trying to push the car in each position.

The downshift cable, or in some cases linkage, provides the transmission with information about the accelerator pedal position which is used to adjust the speeds at which gearchanges occur.

Check for free movement of the cable by manually operating the throttle linkage. The cable should move up freely and return without kinking. If the movement is not free check along the outer cable to make sure it is not kinked or squashed.

Pull on the cable itself to check there is a resistance to movement— if it pulls up freely with no resistance it is broken or has become disconnected in the gearbox. There should be a small amount of free movement in the throttle linkage before the cable, or linkage, comes into action.

You can make minor changes in the cable setting by releasing the locknut and using the adjusting screw. Make only small changes and check the effect by road testing.

Automatic Car Gears Explained

Most automatic transmissions are fitted with an inhibitorswitch which lets you start the engine only when the transmission is in the 'neutral' or 'park' positions — often the switch includes an additional set of contacts for the reversing lights. Failure of the switch, or the associated wiring, will mean that you will not be able to operate the starter.

However, before you check the switch, try to start the engine in all the control lever positions because the problem could lie with the control linkage. If the starter will operate in any position other than 'park' and 'neutral', the linkage needs adjusting. Common positions for the inhibitor switch are on the transmission housing (close to the selector lever); at the end of the cable-operated control linkages (in front-wheel-drive cars); and by the side of the control handle inside the car. Using a test lamp check that there is a power supply to the inhibitor switch when the starter is being operated — you will need someone to help with this.

Then see if power appears on the output side of the switch when the selector lever is in the 'park' or 'neutral' position. If it does not, the switch needs adjusting or replacing. With some transmissions the switch can be adjusted by releasing a locknut and screwing the switch assembly into, or out of, its mounting.

Automatic Car Gears 1 2 3 For

Where the switch is by the control handle, adjustment is generally made by releasing the contact assembly mounting screws and sliding the assembly into a new position. After making any adjustments check that the starter will only operate in 'park' and 'neutral'. If you cannot get the switch to work by adjusting it, you will have to fit a new one.

Incorrect alignment of the linkage between the control lever and the transmission can cause a variety of problems such as an inability to start the engine or to engage drive.

Automatic Transmission Cars

The precise method of adjustment varies with the type of transmission and the linkage design but the normal procedure is to disconnect the linkage where it connects to the selector lever on the transmission. The lever on the transmission and the selector inside the car are set to the same control position, generally 'drive' or 'park', and the linkage alignment checked.